How to Set up a Tub: Install an Acrylic Bathtub as Well as Tub Surround
How to Set up a Tub: Install an Acrylic Bathtub as Well as Tub Surround
Blog Article
This great article in the next paragraphs in relation to A Step-by-Step Guide to Installing a Bathtub is especially entertaining. You should check this stuff out.
Mounting a tub isn't exactly rocket science, yet it does call for solid plumbing, carpentry, and sometimes, tiling abilities. Replacing an old bath tub with a new one is also a moderately hard task. If the old tub is readily accessible, the task can relocate rapidly; if you have to open up a wall to eliminate the old tub and also place the new bath tub, the job is much harder. In either case, the task is within a house handyman's skills, although you will certainly need a helper to move out the old bathtub as well as set in the brand-new one. Ensure you have actually certified yourself for the work as well as are comfortable trying it. Instead of hiring a service provider to take over a halfway-completed task, it is much better to consider using one before you start. Possibilities are you may require an expert plumber to make tube connections.
This write-up will aid you set up a new tub in your washroom if you have actually already purchased a brand-new tub and do not require to alter the arrangement of your previous water pipes.
Your devices and product checklist must comprise the following:
Preparing for the Setup
To start with, the supporting frame supplied with the bathroom should be fitted (if needed) according to the supplier's guidelines. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is important to ensure that if the tap includes a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bath, it is additionally sensible to fit a supporting plate under the faucets device to prevent stress on the tub.
Fit the adaptable faucet connectors to the bottom of the two faucets using 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet through the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you utilize every one of the provided washing machines.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its last placement.
Removing Old Taps
If you need to replace old taps with new ones as a part of your installation, then the first thing you should do is separate the water supply. After doing so, activate the faucets to drain any water continuing to be in the system. The procedure of getting rid of the existing faucets can be fairly bothersome as a result of the limited accessibility that is usually the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the taps. Have a cloth ready for the remaining water that will come from the pipes. As soon as the supply pipelines have actually been eliminated, make use of the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single taps from transforming during this process. Once the taps have actually been eliminated, the holes in the bath/basin will have to be cleaned of any type of old sealing substance.
Prior to carrying on to fit the new taps, contrast the pipeline links on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.
Mounting the Bath tub
Utilizing the two wooden boards under its feet, position the bath tub in the needed setting. The wood boards are useful in evenly spreading out the weight of the tub over the area of the boards as opposed to focusing all the weight onto 4 little points.
The next objective is to make sure that the bathtub is leveled all round. This can be attained by inspecting the level and also changing the feet on the bathtub up until the level checks out level.
To set up taps, fit all-time low of the furthest adaptable tap adapter to the proper supply pipeline by making a compression join; after that do the same for the various other tap.
Activate the water system and inspect all joints and brand-new pipework for leaks as well as tighten them if necessary. Fill the tub and likewise examine the overflow outlet and also the typical electrical outlet for leaks.
Ultimately, fix the bath paneling as defined in the producer's instruction manual. Tiling and also securing around the bathtub must wait until the bath tub has been made use of a minimum of when as this will resolve it into its last setting.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will require a plastic port to stop damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end offers a link to the existent supply pipes.
If you require to fit a monobloc, after that you will need lowering couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the tap in the installing opening in the bath/basin ensuring that the washers remain in area between the tap as well as the sink. Safeguard the tap in place with the maker given backnut. As soon as the faucet is safely in position, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular faucet connectors. The former type must be attached to the faucet ends first, tightening only by hand. The supply pipelines can later be connected to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bathroom meets the tile, it is required to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to split a stiff seal, creating the water to pass through the wall surface in between the bathroom as well as the tiling, bring about difficulties with wetness and also feasible leaks to the ceiling below.
You can choose from a variety of coloured sealants to blend in your components and also fittings. They are offered in tubes and cartridges, and can securing voids approximately a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with spins of drenched paper or soft rope. Bear in mind to constantly load the tub with water before sealing, to allow for the activity experienced when the bathtub remains in usage. The sealant can break fairly early if you do not take into consideration this movement before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise quickly readily available on the marketplace. It is a good idea to fit the ceramic tiles using waterproof or water resistant adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a devoted person who reads about How to Install a Bathtub Yourself, I imagined sharing that segment was a great idea. Kindly take the opportunity to distribute this blog if you enjoyed it. Thanks a bunch for your time. Please visit our website back soon.
Schedule Now
Report this page